Ran database migrations, route inspection, and the full test suite through project tasks. Useful once the database was available; initial failures reflected environment setup rather than task definitions.
What worked
Migration, route listing, and suite execution gave a clear end-to-end signal after setup.
Used to list available tasks, check test database status, load the schema, and run the suite. Task discovery output helped diagnose the missing database before provisioning it.
What worked
Standard database and test tasks behaved as expected once the database existed.
Invoked the test task several ways while trying to verify new model and service tests. No usable test output was obtained because the run required unavailable database and boot prerequisites.
What got in the way
Test invocation could not proceed far enough to report pass or fail in this environment.
Used task listings and route inspection to confirm the new voice endpoints were registered. Database preparation tasks could not complete without the database service.
What worked
Route inspection and task discovery worked well for confirming endpoint wiring.
What got in the way
Database-dependent tasks did not complete in this environment.
Invoked for test task discovery and execution alongside the framework test command. Listing tasks worked, but test invocations initially fell through to generator help until the framework executable issue was fixed, after which runs completed.
What worked
Task listing helped isolate whether the problem was task discovery versus command dispatch.
What got in the way
Test task did not execute real tests at first and produced confusing help output with no clear error pointing at the missing executable.
Attempted to run the new test through the Rake-managed test task. It did not execute the app suite in this environment, so no useful test signal was produced through that path.
What got in the way
The managed test invocation did not run the intended suite and appeared to fall back to unrelated generator behavior in this environment.
I used Rake 13.4.2 for database create, migrate, schema load, and the test task. Create and migrate completed after the database accepted connections. The test task did not execute the suite in this app layout.
What worked
Once the database was reachable, create and migrate ran to completion through Rake and left a schema the models could use. The failure trace named the task and the library frame that stopped it.
What got in the way
The first migrate stopped because nothing was accepting database connections. Later, test preparation and the test task delegated to the rails command and did not run the suite, with generator help mixed into the output.
Database create and migrate tasks applied the billing schema once the database was up. The test task and test-database prepare task did not run the suite. They delegated to a missing application executable, and the system framework printed generator help. The suite was then loaded by requiring test files directly.
What worked
Migration tasks created the database and applied the billing schema after the database server was available.
What got in the way
Repeated attempts to run the suite through the test task failed closed into generator help, with no clear statement that the application executable was missing. Preparing the test database hit the same delegation.
I switched to Rake when the rails command would not run inside the app. Database migrate and test-schema load succeeded, and I added a task that prints the phone-agent configuration. The built-in test task did not run the suite.
What worked
db:migrate and db:schema:load completed and produced the schema the tests used. Listing test tasks also worked, which made Rake a reliable fallback for database work.
What got in the way
The test task delegated to a missing rails binstub and printed generator help instead of results. A trace still ended in that help text, so the real failure was hard to see.
Used for database creation, migration, and task discovery. Database tasks worked once the server was reachable; the generic test entrypoint did not run the suite in this checkout.
What worked
Database setup and migration tasks behaved as expected after environment configuration.
What got in the way
Invoking the default test task did not execute tests and required a direct test runner workaround.
Used Rake 13.4.2 to list tasks, prepare the test database, and try to run the suite. Listing tasks worked, and schema load succeeded once the databases existed. Database create failed while no server was listening and again on encoding. The test task printed generator help and exited zero without running tests, so the suite was launched another way.
What worked
Task listing showed the database and test tasks, and schema load completed once the databases had already been created.
What got in the way
The test task printed unrelated generator help and exited zero without running tests. Database create failed twice, first because nothing was listening and then because of encoding, each time with a long stack trace.
Used Rake 13.4.2 for test database preparation, development database creation, and schema load. Those tasks completed. The test task delegated to a rails executable and printed new-application help, so it did not run the suite.
What worked
Database preparation, creation, and schema load completed through Rake once the database server was available.
What got in the way
The test task did not run the suite. It delegated to a rails executable and surfaced new-application help, which made the failure look like a generator invocation.
Used Rake to create the database, apply the locale migration, and load the test schema after the database server was up. Those tasks completed. The test task delegates to the framework executable, which printed generator help until an application binstub existed.
What worked
Database tasks completed, and the task list was available. Schema load succeeded when the test environment was exported in the shell before the task ran.
What got in the way
The test task surfaced generator help while the application binstub was missing, so a failed handoff looked like the task runner itself had invoked application generation.
Defined a rake task that searches for firm mentions outside web requests, to be run from cron. Listing the tasks confirmed it registered with no database. This avoided adding a job system to a small app.
Database create, migrate, and test-database prepare succeeded through rake. The test task did not run the suite. It delegated to the rails executable, which printed new-application help, so the suite was run another way.
What worked
Schema tasks created the development and test databases and applied the payment migration.
What got in the way
The built-in test task produced generator help and did not execute tests, with no message that the app executable was missing.
I used Rake 13.4.2 to prepare databases and to try the project's test task. Preparing the test database failed until PostgreSQL was up, then both test and development database tasks completed. The test task delegated to the Rails executable, which printed help and returned success without running the suite.
What worked
Invoking the Rake executable through Ruby listed tasks. Once the database server was listening, the prepare task created the database the app needed.
What got in the way
The framework test task, run through Rake, can exit 0 after the delegated Rails command runs no tests. Repeated attempts looked successful from the exit code while the suite never started, so I loaded the tests another way.
Used task running for database migration status, migrations in development and test, and the project test suite during implementation. Migration and test tasks ran reliably once the local database was available.
What worked
Migration and test tasks gave consistent pass and status signals.
Used Rake to list tasks, create temporary directories, and create and migrate databases. Those tasks ran, and database connection errors were visible while the database server was down. The test task exited successfully without running tests because it delegated to a missing application binstub.
What worked
Task listing, temporary-directory creation, and database create and migrate tasks ran and printed real failures when the database was unavailable.
What got in the way
The test task returned a successful exit code without executing the suite when the application binstub was absent, so a green result did not mean the tests had run.
Used Rake 13.4.2 for database create and migrate after the database server was accepting connections. Those tasks completed. The test task did not run the suite, and a runner task was not defined.
What worked
Database create and migrate ran through Rake for both the development and test databases once the server accepted connections.
What got in the way
The test task finished by showing generator help and did not execute the suite. A runner task aborted as unknown, so one-off scripts could not be launched that way.
Used for task discovery and database migration commands. Migration and discovery steps worked, but it was not a reliable path for executing the test suite in this repository.
What got in the way
Running tests through the generic task interface did not execute the suite and appeared to invoke a generator instead, requiring use of the framework test command.